Effect of feed rate and depth of cut on face milling process on surface roughness of Al-Mg alloy using CNC milling machine 3 axis
Article Sidebar
Main Article Content
Abstract
The purpose of this study was to determine the effect of feed rate and depth of cut on the surface roughness of Al-Mg aluminum using a DIY CNC Milling Machine and Krisbow Universal Milling Machine as a comparison. The open-loop control system is a control system used in the design of DIY CNC Milling machines. A PC with Mach3 software is used as a PC Based Direct Digital Controller to control the system. In this study, the feed rate variation 24 mm/minute and 42 mm/minute and depth of cut 0.25 mm, 0.5 mm, and 0.75 mm were used. After the face milling process, the surface roughness test was carried out using the Mitoyo Surface Roughness Tester to determine the level of surface roughness of the machining results the DIY Milling Machine and Krisbow Universal Milling Machine as a comparison. The results showed that as the feed rate and depth of cut increased, the surface roughness values of both tools increased.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
Hyungjung Kim, Woo-Kyun Jung, In-Gyu Choi, Sung-Hoon Ahn, A Low-Cost Vision-Based Monitoring of Computer Numerical Control (CNC) Machine Tools for Small and Medium-Sized Enterprises (SMEs) Inc., Sensors, 19, 4506, 2019
Mohammad Kamruzzaman Khan Prince, Muhsi-Al-Mukaddem Ansary, Abu Shafwan Mondol, Implementation of a Low-cost CNC Plotter Using Spare Parts, International Journal of Engineering Trends and Technology, V43(6),333-339 January 2017
Hamed Aghajani Derazkola, Arameh Eyvazian, Abdolreza Simchi, Submerged friction stir welding of dissimilar joints between an Al-Mg alloy and low carbon steel: Thermo-mechanical modeling, microstructural features, and mechanical properties, Journal of Manufacturing Processes, 50, 68-79, 2020
Janos Kundrak, Angelos P. Markopoulos, Tamas Makkai , Istvan Deszpoth, Antal Nagy, Analysis of the Effect of Feed on Chip Size Ratio and Cutting Forces in Face Milling for Various Cutting Speeds, Manufacturing Technology, 18(3), 431-438, 2018
Sekulic, M., Pejic, V. , Brezocnik, M. , Gostimirovic, M., Hadzistevic, M., Prediction of surface roughness in the ball-end milling process using response surface methodology, genetic algorithms, and grey wolf optimizer algorithm, Advances in Production Engineering & Management, 13(1), 18-30, 2018
I.Tlhabadira, I.A.Daniyan, L.Masu,L.R.Van Staden, Process Design and Optimization of Surface Roughness during M200 TS Milling Process using the Taguchi Method, Procedia CIRP, 84, 868-873, 2019
Mozammel Mia, Prithbey R.Dey, Mohammad S.Hossain, Md T.Arafat, Md Asaduzzaman, Md. Shoriat Ullah,S.M.Tareq Zobaer, Taguchi S/N based optimization of machining parameters for surface roughness, tool wear and material removal rate in hard turning under MQL cutting condition, Measurement, 122, 380-391, 2018
Jaehyeon Nam, Hyuncheol Do, Jaeyoung Kang, Investigation of friction induced vibration in lead screw system using FE model and its experimental validation, Applied Acoustics, 122, 98-106, 2017
Lalatendu Dash, Smita Padhan, Sudhansu Ranjan Das, Experimental investigations on surface integrity and chip morphology in hard tuning of AISI D3 steel under sustainable nanofluid-based minimum quantity lubrication, Journal of the Brazilian Society of Mechanical Sciences and Engineering volume 42, Article number: 500, 2020
Junaidi, Soni Hestukoro, Indra Roza, Dian Morfi Nst, Weriono, Process Analysis of High Speed Steel Cutting Calculation (HSS) with S45 C Material on Universal Machine Tool, International Journal of Innovative Science and Research Technology, 3(1), 447-456, 2018